Signs Your Electrical Panel Needs to Be Replaced
Your breaker panel feeds every circuit in the house. When it is too small, too old, or damaged, you may see flickering lights, warm breakers, or trips that keep coming back. Many homes now run more than they did when the panel was new: bigger air conditioners, home offices, pool pumps, and EV chargers.
This is a guide to the warning signs, not a diagnosis. Only a licensed electrician should take the cover off the panel and tell you whether you need a repair, a few new circuits, or a new panel. Do not open the panel yourself.
Morningstar Electric LLC, Lic# EC13005732, is an electrical contractor based in the Tampa Bay area with a second office in Big Pine Key. We inspect and replace home panels. See our panel upgrade service.
When a checkup makes sense, even if nothing has failed
The Electrical Safety Foundation International (ESFI) recommends a home electrical inspection, especially if: [1]
The home is 40 or more years old
The home is 10 or more years old and has had a major renovation, an addition, or a major new appliance
You just bought a home someone else owned
Warning signs you should not ignore
ESFI lists these as signs of wiring hazards. If you see any of them, call a licensed electrician to inspect the wiring. [1]
Breakers that trip often, or fuses that often need replacing
Dim or flickering lights
Arcs or sparks anywhere in the electrical system
Sizzling or buzzing sounds from the electrical system
Overheating: a smell of hot insulation, or switch plates and outlet covers that are hot or discolored
Shocks, even a mild tingle
An "overrated" panel, with fuses or breakers rated higher than the circuits they protect
Cut, broken or cracked wire insulation
ESFI also says many existing homes simply can't handle the demands of today's appliances and devices, and that the warning signs include flickering lights and breakers that constantly trip. [2]
If you smell burning or see smoke, get everyone out and call 911. Do not touch the panel. Once everyone is safe, call a licensed electrician.
Things an electrician will look for
When we open a panel, we check for problems like these:
Rust, corrosion, water stains or damp spots in or around the panel
Scorch marks, melted plastic, or discolored metal parts
Loose breakers, or two wires under a screw made for one
An old fuse box, or a small main breaker in a home that now runs central air
No room left for a new circuit, an EV charger, or a whole-house surge protector
Some of these can be repaired. None of them are do-it-yourself fixes.
Older panels that deserve a professional look
Federal Pacific Electric (FPE) Stab-Lok panels often come up on home inspections. Here is what the record says. In 1980 the maker reported to the U.S. Consumer Product Safety Commission (CPSC) that many FPE breakers did not fully meet Underwriters Laboratories (UL) requirements. CPSC testing confirmed that these breakers failed certain UL calibration tests, which check whether a breaker trips in time on an overload. In 1983 the CPSC closed its investigation, saying the data it had did not establish a serious risk of injury, and it made no finding either way on the breakers' safety. It advised everyone to follow basic safety steps with all breakers and fuses. [3]
So there was no recall. If an inspector flags an FPE panel in your home, have a licensed electrician look at it in person. Do not flip breakers to "test" them.
What a panel replacement involves
A permitted panel replacement can include checking the service size you have and the size you need, replacing the panel, labeling every circuit, and adding protection that older panels often lack, such as AFCI and GFCI protection where the code requires it.
It also brings in surge protection. Section 230.67 of the 2020 National Electrical Code (NEC) requires a Type 1 or Type 2 surge protective device as part of, or right next to, the service equipment for homes. NFPA explains that this applies to new services and to service upgrades. [4] The Florida Building Code, 8th Edition (2023), took effect December 31, 2023 [5], and it is based on the 2020 NEC. [6] Your building department enforces the code in force when the permit is pulled, so we confirm that before we start. Learn more about whole-house surge protection.
Every house is different, so we do not post prices. We need to see the panel first.
What you can do safely
Look at the panel label and note any circuits that are not marked.
Write down which breakers trip and when.
Unplug overloaded power strips.
If a breaker trips, find out why before you reset it. The CPSC says a trip is often a warning that the circuit is overloaded, and to call a licensed electrician when in doubt. [3]
Never put in a bigger breaker or fuse "so it stops tripping," and never work inside the panel.
Call for a quote
If any of these signs sound familiar, we can look at your panel and tell you what we see, in plain words.
TAMPA BAY: 813-892-4582
LOWER KEYS: 305-897-1698
Morningstar Electric LLC, Lic# EC13005732. Getting ready for storm season too? See our storm prep page.
Sources
CPSC, Commission Closes Investigation of FPE Circuit Breakers (1983, revised 2011)
NFPA, Changes to the 2020 NEC That Impact How We Install Residential Electrical Services (2021)
Florida Building Commission, Florida Building Code Effective Dates
ICC, Significant Changes to the Florida Building Code 2023 Edition (sample pages)



Comments